Electrocatalytic Oxygen Reduction Using Metastable Zirconium Suboxide.

Strategies for discovery of high-performance electrocatalysts are important to advance clean energy technologies. Metastable phases such as low temperature or interfacial structures that are difficult to access in bulk may offer such catalytically active surfaces. We report here that the suboxide Zr3O, which is formed at Zr-ZrO2 interfaces but does not appear in the experimental Zr-O phase diagram exhibits outstanding oxygen reduction reaction (ORR) performance surpassing that of benchmark Pt/C and most transition metal-based catalysts. Addition of Fe3C nanoparticles to give a Zr-Zr3O-Fe3C/NC catalyst (NC = nitrogen-doped carbon) gives a half-wave potential (E1/2) of 0.914 V, outperforming Pt/C and showing only a 3 mV decrease after 20,000 electrochemical cycles. A zinc-air battery (ZAB) using this cathode material has a high power density of 241.1 mW cm-2 and remains stable for over 50 days of continuous cycling, demonstrating potential for practical applications. Zr3O demonstrates that interfacial or other phases that are difficult to stabilize may offer new directions for the discovery of high-performance electrocatalysts.

Vertical Cross-Alignments of 2D Semiconductors with Steered Internal Electric Field for Urea Electrooxidation via Balancing Intermediates Adsorption.

Single-component electrocatalysts generally lead to unbalanced adsorption of OH- and urea during urea oxidation reaction (UOR), thus obtaining low activity and selectivity especially when oxygen evolution reaction (OER) competes at high potentials (>1.5 V). Herein, a cross-alignment strategy of in situ vertically growing Ni(OH)2 nanosheets on 2D semiconductor g-C3N4 is reported to form a hetero-structured electrocatalyst. Various spectroscopy measurements including in situ experiments indicate the existence of enhanced internal electric field at the interfaces of vertical Ni(OH)2 and g-C3N4 nanosheets, favorable for balancing adsorption of reaction intermediates. This heterojunction electrocatalyst shows high-selectivity UOR compared to pure Ni(OH)2, even at high potentials (>1.5 V) and large current density. The computational results show the vertical heterojunction could steer the internal electric field to increase the adsorption of urea, thus efficiently avoiding poisoning of strongly adsorbed OH- on active sites. A membrane electrode assembly (MEA)-based electrolyzer with the heterojunction anode could operate at an industrial-level current density of 200 mA cm-2. This work paves an avenue for designing high-performance electrocatalysts by vertical cross-alignments of active components.

Activating Interfacial Electron Redistribution in Lattice-Matched Biphasic Ni3N-Co3N for Energy-Efficient Electrocatalytic Hydrogen Production via Coupled Hydrazine Degradation.

The development of high-purity and high-energy-density green hydrogen through water electrolysis holds immense promise, but issues such as electrocatalyst costs and power consumption have hampered its practical application. In this study, we present a promising solution to these challenges through the use of a high-performance bifunctional electrocatalyst for energy-efficient hydrogen production via coupled hydrazine degradation. The biphasic metal nitrides with highly lattice-matched structures are deliberately constructed, forming an enhanced local electric field between the electron-rich Ni3N and electron-deficient Co3N. Additionally, Mn is introduced as an electric field engine to further activate electron redistribution. Our Mn@Ni3N-Co3N/NF bifunctional electrocatalyst achieves industrial-grade current densities of 500 mA cm-2 at 0.49 V without degradation, saving at least 53.3 % energy consumption compared to conventional alkaline water electrolysis. This work will stimulate the further development of metal nitride electrocatalysts and also provide new perspectives on low-cost hydrogen production and environmental protection.

Cu-Pt/CrN Fuel Cell Gas Sensor Achieves ppb-Level H2S Detection at Room Temperature.

Fuel cell gas sensors have emerged as promising advanced sensing devices owing to their advantageous features of low power consumption and cost-effectiveness. However, commercially available Pt/C electrodes pose significant challenges in terms of stability and accurate detection of low concentrations of target gases. Here, we introduce an efficient Cu-Pt/CrN-based fuel cell gas sensor, designed specifically for the ultrasensitive detection of hydrogen sulfide (H2S) at room temperature. Compared to the commercial Pt/C sensor, the Cu-Pt/CrN sensor exhibits excellent sensitivity (0.26 µA/ppm), with an increase in the selectivity by a factor of 2.5, and demonstrates good stability over a 2 month period. The enhanced sensing performance can be attributed to the modulation of the electronic arrangement of Pt by Cu, resulting in an augmentation of H2S adsorption. The Cu-Pt/CrN fuel cell gas sensor provides an opportunity for detecting parts per billion-level H2S in various applications.

Metal nitrides for seawater electrolysis.

Electrocatalytic high-throughput seawater electrolysis for hydrogen production is a promising green energy technology that offers possibilities for environmental and energy sustainability. However, large-scale application is limited by the complex composition of seawater, high concentration of Cl- leading to competing reaction, and severe corrosion of electrode materials. In recent years, extensive research has been conducted to address these challenges. Metal nitrides (MNs) with excellent chemical stability and catalytic properties have emerged as ideal electrocatalyst candidates. This review presents the electrode reactions and basic parameters of the seawater splitting process, and summarizes the types and selection principles of conductive substrates with critical analysis of the design principles for seawater electrocatalysts. The focus is on discussing the properties, synthesis, and design strategies of MN-based electrocatalysts. Finally, we provide an outlook for the future development of MNs in the high-throughput seawater electrolysis field and highlight key issues that require further research and optimization.